Flat Roof Leak Repair in Florida means finding the actual breach, not smearing sealant over a stain. Our licensed crews handle TPO membrane, EPDM rubber, and modified bitumen on homes, strip centers, and warehouses from Jacksonville to Cape Coral. If your ceiling is spotting after an afternoon storm, we can usually be on the roof the same day and stop the water before it reaches your drywall.
Flat Roof Leak Repair in Florida is the process of locating water intrusion on a low-slope roof and restoring the membrane, flashing, and seams so the assembly sheds water again. On a Florida flat roof, that usually means inspecting TPO membrane or EPDM rubber for punctures, checking every pipe boot and roof flashing detail, and probing seams with a moisture meter before we cut anything open. Water travels sideways under insulation, so the wet spot on your ceiling is rarely directly under the hole.
Most Florida flat roof leaks start at the same handful of details: a failed pipe boot, a seam that opened after a summer of thermal cycling, or flashing pulled loose by hurricane wind. If you have been searching for flat roof leak repair near me Florida and getting nothing but callbacks that never come, we run 24/7 dispatch across the state and tarp first when rain is still in the forecast. Typical 2026 pricing for a straightforward repair runs $350 to $1,200 depending on access and membrane type.
Every flat roof repair starts with a real diagnosis and ends with a water test. Here is what is covered in a standard repair, and what we price separately when the roof needs more than a patch.
A licensed technician walks the entire roof with a moisture meter and inspection camera, checking seams, flashing, pipe boots, drains, and penetrations. You get photos of every failure point and a plain-English explanation of what is leaking and why.
We cut back the failed membrane, dry the deck, and install new TPO membrane, EPDM rubber, or modified bitumen as the roof requires. Seams are heat-welded or chemically spliced to manufacturer spec, not caulked and forgotten.
Wall flashing, curb flashing, edge metal, and pipe boots are rebuilt with new material, butyl tape, and substrate-rated sealant. These details cause most flat roof leaks in Florida, so we do not shortcut them.
We flood-test or hose-test the repaired area and watch it from inside when access allows. If water still shows up, we keep working. You do not pay for a repair that has not been proven.
Magnets sweep the lawn and driveway for fasteners, and we haul away all old membrane and debris. Before we leave, we walk you through the repair and tell you what to watch for over the next two weeks.
You call (833) 356-1017 and describe what you are seeing: a ceiling stain, water at a light fixture, a puddle on the roof deck. We ask the questions that tell us whether you need emergency tarping tonight or a scheduled repair tomorrow morning. Most calls get a same-day window.
A licensed technician walks the roof with a moisture meter and inspection camera, checking seams, pipe boots, flashing, drains, and penetrations. We photograph everything and show you the actual failure point. This takes 45 to 90 minutes on a typical commercial roof.
You get a written scope with the repair method, materials, and a fixed price before we start. No surprise line items. If the honest answer is that a full re-roof makes more sense than a patch, we tell you that too and show you why.
We cut back the failed membrane, dry the deck, and rebuild the detail with roof flashing, butyl tape, and the correct sealant for the substrate. TPO gets heat-welded; EPDM gets splice adhesive and primer. Most repairs are finished in two to six hours.
Before we leave, we flood-test or hose-test the repaired area and watch it from inside if access allows. Magnets sweep the lawn and driveway for fasteners, and we walk you through what we did and what to watch for over the next two weeks.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Reads water content in insulation and decking so we can map the wet area before opening the membrane. This is how we avoid exploratory cuts that cost you money.
Lets us see inside drains, curbs, and wall cavities where a leak often starts. We document what we find with photos you get in the written scope.
Used for fastening new membrane, base sheet, and flashing on repairs that require mechanical attachment. Every fastener is set to manufacturer spec.
Applies Henry, DAP, and Geocel sealants at terminations, penetrations, and flashing edges. We match the sealant to the substrate so it bonds and stays flexible.
Used to lift edge metal and cut back failed membrane cleanly so the new material bonds to sound substrate instead of contaminated surface.
OSHA-compliant fall protection on every low-slope roof. Our crews do not walk a roof edge without it, and that discipline shows in the quality of the work.
A homeowner had a spreading brown ring on the ceiling after every afternoon storm. Two previous companies had caulked the same spot twice, and the leak kept returning within weeks.
We moisture-mapped the flat roof section, found a failed pipe boot and an open seam near the AC curb, and rebuilt both details. The repair took four hours and cost $680. The ceiling has stayed dry through two storm seasons.
A 40,000-square-foot TPO warehouse roof was leaking onto inventory racks during summer storms. The seam had opened over 12 feet, and two pipe boots were cracked and brittle from UV exposure.
We tarped the area the same day, then heat-welded a new seam section and replaced both pipe boots. The repair was completed in two days for $4,200, and the roof passed a full flood test before we left.
A property manager had three tenants reporting leaks after a tropical system. The edge metal was corroded and pulled loose, and water was running down the wall flashing into two suites.
We replaced 60 feet of edge metal, rebuilt the wall flashing with butyl tape and new sealant, and repaired the membrane at each penetration. All three leaks stopped, and the work was documented for the insurance claim.
Flat roofs fail in predictable ways, and Florida weather accelerates every one of them. Here are the problems we fix most often and what happens when they are ignored.
Ask a pro →We trace the leak to its actual source with a moisture meter, repair the membrane or flashing detail, and water-test before leaving. Most repeat-stain calls are a single failed pipe boot or seam that was never correctly diagnosed.
We find why the roof is not draining, clear or repair the drains, and correct the low spots where the deck has settled. If the ponding is structural, we tell you and price the fix honestly instead of patching over it.
We run 24/7 emergency tarping across Florida from June through November. A tarp goes down first to stop the water, then we schedule the permanent flat roof repair as soon as the weather clears and the roof is dry.
We remove the failed sealant, clean and prime the substrate, and reapply a product rated for that specific material. On commercial roofs we often recommend a maintenance program that reseals details on a set schedule.
Most single-point flat roof leak repairs in Florida run $350 to $1,200 in 2026, including materials and labor. Cost climbs with roof height, membrane type, and how much wet insulation has to be replaced. A simple pipe boot reseal on an accessible carport might land near $350, while a seam rebuild on a 40,000-square-foot TPO warehouse roof can run several thousand. You get a fixed written price before we start.
The four most common causes we find are failed pipe boots, open membrane seams, flashing pulled loose by wind, and clogged drains that pond water until it finds a weak point. Florida's UV load and daily thermal cycling age sealant faster than in cooler states, so a detail that lasts 15 years up north may need attention at year eight here. Regular inspections catch most of these before they leak.
Yes, most flat roof leaks can be repaired without a full replacement, provided the membrane is still sound and the wet area is limited. We cut back the failed section, dry the deck, and rebuild the detail with new membrane and flashing. If more than about 25 percent of the roof shows saturation or the membrane is brittle across the field, we will show you the evidence and price a replacement instead.
A typical single-point repair takes two to six hours on site, and we can often complete it the same day you call. Larger commercial repairs with multiple failure points may run one to three days depending on roof size and material availability. Emergency tarping goes down within hours of your call when rain is still in the forecast, and the permanent repair follows as soon as the roof is dry.
Our flat roof repair crews cover the whole state, from the Atlantic coast to the Gulf. Whether you need a same-day fix on a residential flat roof or a scheduled repair on a commercial building, we bring the same licensed technicians, moisture-meter diagnostics, and fixed written pricing to every job. Call (833) 356-1017 and we will tell you exactly when we can be there.
Emergency Roof Leak RepairWhen water is actively coming through a ceiling or light fixture, emergency roof leak repair stops the damage before the permanent fix. We tarp, isolate the source, and schedule the flat roof repair as soon as conditions allow.Explore →
Roof Flashing RepairFlashing failure is one of the top causes of flat roof leaks in Florida. We rebuild wall, curb, and edge flashing with new metal, butyl tape, and sealant so the perimeter stops leaking and the repair matches the rest of the roof.Explore →
Pipe Boot RepairCracked pipe boots are the single most common flat roof leak we find. We replace the boot with a UV-rated unit and seal it to the membrane, which usually solves the leak in under two hours.Explore →
Missing Shingle Roof RepairOn low-slope-to-steep transitions, missing shingles let water back up under the flat roof edge. We replace the shingles and tie the transition flashing into the flat membrane so both roof sections shed water correctly.Explore →
Tile Roof Leak RepairTile roofs leak at valleys, hips, and underlayment, and the water often shows up on a flat roof section below. We repair the tile detail and the underlayment so the flat roof is not carrying water it was never meant to handle.Explore →
Chimney Roof Leak RepairChimney flashing and counter-flashing fail with age, sending water onto flat roof sections at the base. We rebuild the flashing and seal the masonry transition so the leak stops at the chimney instead of spreading across the roof.Explore →
Skylight Leak RepairSkylight curbs on flat roofs leak at the sealant line and the curb flashing. We re-flash the curb, replace failed sealant with a substrate-rated product, and water-test the unit before we leave.Explore →
Emergency Roof TarpingWhen a storm opens your roof, emergency tarping keeps water out until permanent repairs can happen. We secure the tarp with weighted and fastened edges so it holds through the next round of wind and rain.Explore →One call gets a licensed technician on your roof, a moisture-meter diagnosis, and a fixed written price. We have been doing this since 1997, and we answer the phone 24/7. Call now and stop the water before the next storm.
Schedule My Repair (833) 356-1017 →Call us at (833) 356-1017 any time, day or night. We answer live, and for active leaks we dispatch the nearest crew immediately. You can also email info@weatherproofroofinginc.com with photos of the damage and we will respond the same business day. We serve the entire state of Florida.